¡@

Home 

c++ Programming Glossary: baud

Boost Asio serial_port - need help with io

http://stackoverflow.com/questions/267752/boost-asio-serial-port-need-help-with-io

serial_port port io COM3 port.set_option serial_port_base baud_rate 19200 unsigned char commands 4 1 128 240 0 write the commands.. c boost share improve this question In addition to the baud rate you may also need to set other options like character_size..

How do I configure and communicate with a serial port?

http://stackoverflow.com/questions/3049/how-do-i-configure-and-communicate-with-a-serial-port

How do I figure out what the configuration settings e.g. baud rate should be and how do I set them In particular I am looking.. How do I figure out what the configuration settings e.g. baud rate should be... Read the datasheet Ok ok. Seriously last one... datasheet Ok ok. Seriously last one. If you don't know the baud rate of the device you are trying to communicate with you have..

High delay in RS232 communication on a PXA270

http://stackoverflow.com/questions/4667141/high-delay-in-rs232-communication-on-a-pxa270

a packet from the external device via RS232 115200 baud until it sends an ACK custom packet back to the external device... ... and set them to the desired values cfsetispeed options baudRate cfsetospeed options baudRate no parity 8N1 options.c_cflag.. values cfsetispeed options baudRate cfsetospeed options baudRate no parity 8N1 options.c_cflag ~PARENB options.c_cflag ~CSTOPB..

How to set baud rate to 307200 on Linux?

http://stackoverflow.com/questions/4968529/how-to-set-baud-rate-to-307200-on-linux

to set baud rate to 307200 on Linux Basically I'm using the following code.. Linux Basically I'm using the following code to set the baud rate of a serial port struct termios options tcgetattr fd options.. But know I have to communicate with a device that uses a baud rate of 307200. How can I set that cfsetispeed options B307200..

How to use Boost.Asio c++?

http://stackoverflow.com/questions/5537016/how-to-use-boost-asio-c

m_io_service std string m_name const unsigned int m_baud_rate const enum flow_control type m_flow_control const enum.. name for example COM1 windows or dev ttyS0 linux . @param baud_rate The baud rate. @param flow_control The flow control. Acceptable.. COM1 windows or dev ttyS0 linux . @param baud_rate The baud rate. @param flow_control The flow control. Acceptable values..

ReadFile() says it failed, but the error code is ERROR_SUCCESS

http://stackoverflow.com/questions/5685090/readfile-says-it-failed-but-the-error-code-is-error-success

L COM3 for reference the device communicates at 115200 baud no parity 1 stop bit no flow control open gps com port hGpsUart..

Serial Comm using WriteFile/ReadFile

http://stackoverflow.com/questions/6036716/serial-comm-using-writefile-readfile

file port system_error getting comm state if BuildCommDCB baud 19200 parity n data 8 stop 1 port system_error building comm..

Read and Write on serial port in Ubuntu with C/C++ and LibSerial

http://stackoverflow.com/questions/9046649/read-and-write-on-serial-port-in-ubuntu-with-c-c-and-libserial

Could not open serial port. std endl exit 1 Set the baud rate of the serial port. serial_port.SetBaudRate SerialStreamBuf.. if serial_port.good std cerr Error Could not set the baud rate. std endl exit 1 Set the number of data bits. serial_port.SetCharSize..